1.CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
|
UN NO:
|
None allocated
|
D.G. Class:
|
None allocated
|
Pack. Group:
|
None allocated
|
|
HAZCHEM:
|
None allocated
|
SUB. RISK:
|
None allocated
|
SUSDP:
|
None allocated
|
PROPER SHIPPING NAME
:
Duro AC,
Duro AC CLEAR
PRODUCT USE:
Waterproof Membrane Coating
2. COMPOSITION / INFORMATION ON INGREDIENTS
|
Component
|
CAS No
|
Weight %
|
|
Latex Emulsion Not Required
|
Not Required
|
>30
|
|
Titanium dioxide
|
13463-67-7
|
0-10
|
|
Inorganic extenders
|
Not Required
|
0-50
|
|
Additives
|
Not Required
|
<10
|
|
Water
|
7732-18-5
|
20-50
|
See Section 8, Exposure Controls / Personal Protection
3. HAZARDS IDENTIFICATION
Not hazardous in normal industrial use.
4. FIRST AID MEASURES
Eyes:
Immediately flush with water for 15 minutes. Get medical advice if irritation develops or
persists.
Skin:
Take of all contaminated clothing.
Wash contaminated area with soapy warm water. Get
medical advice if irritation develops or persists.
Wash contaminated clothing and clean
shoes before reuse.
Inhalation:
Remove to fresh air. If not breathing, give artificial respiration, preferable mouth to mouth. If
breathing is laboured, give oxygen and consult a physician immediately.
Ingestion:
Consult a physician immediately. If vomiting occurs, aspiration into the lungs may cause
lung damage. Never give anything by mouth to an unconscious person.
5. FIRE FIGHTING MEASURES
Flash Point: Not Applicable
Auto-ignition Temperature: No data available
Lower Explosive Limit: No data available
Upper Explosive Limit: No data available
Suitable Extinguishing Media:
Use as appropriate for surrounding fire.
Protective Equipment for Fire Fighting:
Wear self-contained breathing apparatus and protective clothing to prevent contact with skin and eyes.
Unusual Fire and Explosion Hazards:
The product is not flammable.
Thermal decomposition of this product may produce toxic fumes.
6. ACCIDENTAL RELEASE MEASURES
Caution: Floor may be slippery. Eliminate all sources of ignition. Provide sufficient ventilation. Wear
appropriate personal protective equipment including gloves and safety glasses. Do not breathe vapour.
Contain spill. Do not allow into drains or waterways. Take up with absorbent material (e.g. sand,
vermiculite, or commercially available inorganic absorbent). Use non-sparking tools and equipment. Fill
into suitable containers for disposal.
Dispose of empty containers in accordance with federal, state and local laws.
7. HANDLING AND STORAGE
Handling:
Observe normal standards of industrial hygiene for handling chemicals. Use in a well ventilated
area. Avoid breathing vapour and contact with skin and eyes. Wear gloves, long sleeved shirt,
and eye protection. A sensitised person should not be exposed to the product.
Storage:
Store in tightly sealed containers to protect from atmospheric moisture. Store in a cool and dry
area. Keep away from ignition sources such as fire, flame and sparks.
Empty container warning:
Do not reuse empty drums or containers unless professionally cleaned. Do
not cut, drill, grind or weld on or near empty containers.
Other Precautions:
Do not eat, drink or smoke when using the product.
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
|
|
NOHSC
|
|
|
TWA
|
STEL
|
|
Component
|
(ppm)
|
(mg/m3)
|
(ppm)
|
(mg/m3)
|
|
Acrylic polymer
|
-
|
a
|
-
|
-
|
|
Titanium dioxide
|
-
|
10b
|
-
|
-
|
|
Inorganic extender
|
-
|
10b
|
-
|
-
|
|
Additives
|
-
|
a
|
-
|
-
|
|
Water
|
-
|
a
|
-
|
-
|
a = not listed
b = as nuisance dust
c = per ACGIH
TWA = Time Weighted Average
STEL= Short term Exposure Limit
National Occupational Health and Safety Commission (
Australia)
Respiratory Protection
If vapours and mists occur, a respiratory protection program meeting Australian Standards AS-
1716 and AS-1715 requirements must be followed whenever workplace conditions warrant a
respirator's use. None required if airborne concentrations are maintained below the exposure
limit listed in "Exposure Limit Information"
Eye Protection
Use chemical splash goggles (Australian Standard AS-1337) or approved equivalent. Eye
protection worn must be compatible with respiratory protection system employed. An eye wash
station and safety shower should be available in the work area.
Hand Protection
Impermeable gloves as necessary to prevent skin contact. E.g. Nitrile or neoprene gloves.
Protective Clothing
Clothing made of the following material has excellent resistance: Tyvec, butyl Nitrile rubber or
neoprene.
Engineering Controls (Ventilation)
Use local exhaust ventilation sufficient to maintain exposure levels below exposure limit
concentrations. Refer to Australian Standard AS-1668.
9. PHYSICAL AND CHEMICAL PROPERTIES
Appearance and colour: White (un-tinted) , Clear
State: Viscous Liquid
Odour Characteristic: Mild Acrylic
pH: 7-9
Specific Gravity (Water = 1): 1.26 (AC Clear 1.03)
Vapour Density (Air = 1): Greater than air
Vapour Pressure: No data available
Melting Point: ~0 oC
Boiling Point: ~100 oC
Solubility in Water: Dispersible.
Flash Point: Not Applicable
10. STABILITY AND REACTIVITY
Considered stable under normal conditions of use and handling.
Hazardous decomposition products:
Thermal decomposition may produce acrylic monomers, carbon monoxide, carbon dioxide and
oxide of nitrogen.
11. TOXICOLOGICAL INFORMATION
Acute Data
No data available for the product.
12. ECOLOGICAL INFORMATION
No available data.
13. DISPOSAL CONSIDERATIONS
Do not reuse empty drums or containers unless professionally cleaned. Dispose of waste and empty
containers in accordance with federal, state and local laws.
14. TRANSPORT INFORMATION
Not classified as Dangerous Goods according to the Australian Code for the Transport of Dangerous
Goods by Road and Rail (Sixth Edition). See section 1.
15. REGULATORY INFORMATION
No Available data.
16. OTHER INFORMATION
NOHSC: National Occupational Health and Safety Commission -
Australia
ADG: Australian Code For The Transport Of Dangerous Goods By Road And Rail (Sixth Edition). |
