Highly resilient waterborne acrylic alloy sealer.
ECO-FINISH is based on a waterborne moderately hard acrylic alloy polymer blend. It produces a dry film which is extremely resilient and virtually invisible. It is designed to be penetrative, binding and wear with exceptional adhesion. ECO-FINISH has excellent resistance to water, oils, greases and most dilute cleaning chemicals. ECO-FINISH is able to be used internally and externally.
ECO-FINISH is suitable for sealing a variety of concrete substrates including old concrete floors which have been acid etched and cleaned.
ECO-FINISH is suitable to seal grout between ceramic tiles.
ECO-FINISH is used as a sealer on ceramic substrates eg. terracotta tiles, slate, clay and concrete paving.
ECO-FINISH can be used to seal reconstituted limestone concrete pavers and liquid limestone paving.
ECO-FINISH has a virtually invisible finish.
ECO-FINISH can be used externally or internally.
ECO-FINISH has UV resistance.
ECO-FINISH has long life durability.
ECO-FINISH has little effect on the original colour of the substrate.
ECO-FINISH is suitable for pedestrian traffic and light vehicle traffic when fully cured.
ECO-FINISH is able withstand puddle water for a reasonable period, but not in a fully immersed static state, e.g. water features.
Stir thoroughly before use. Paint mixer on an electric drill is recommended. Mix for approximately 2 mins before use at low to medium speed.
BARE CONCRETE/CLAY/RECONSTITUTED: Any oil and grease should be removed with MARCMOVE before water blasting. The concrete should be free of dust, dirt, oil, mould, algae, fungi, laitance and should have a sound, firm surface which does not give way when given the packaging tape adhesion test. Allow the surface to dry thoroughly after water blasting with a high pressure machine. Allow the surface to dry thoroughly before applying the ECO-FINISH.
CERAMIC TILES: Make sure there is no grout scum on the surface of the tiles. If so, acid clean with DYNACLENE diluted 10 times with water. Treat as bare concrete as detailed above after the DYNACLENE acid etching. If the tiles are clean and in very good condition, clean them with a vinegar/methylates spirits mixture and water. Rinse well with water, thoroughly dry tiles before sealing.
PAINTED SURFACES: The concrete should be free of dust, dirt, oil, mould, algae, fungi, laitance and should have a sound, firm surface which does not give way when given the packaging tape adhesion test.
Allow the substrate to dry thoroughly before applying the ECO-FINISH. Do not apply under 16 degree C.
SEAL COAT ON UNGLAZED TILES: Apply one or two coats of ECO-FINISH at 6 - 8m2/litre/coat.
PAINTED CONCRETE: Apply one coat of ECO-FINISH at 8-10m2/litre.
CONCRETE, RECON. LIMESTONE PAVING : Apply one coat at 7-8m2/litre/coat.
CLAY PAVERS: Apply one coat at 7-8m2/litre/coat.
LIQUID LIMESTONE CONCRETE: Apply one coat at 4-5m2/litre/coat.
CERAMIC TILE GROUT: Apply one coat not to excess with a switch brush. For highly absorbent grouts, apply a similar coat to the first coat. Surface texture (roughness) and porosities will have an effect on the amount used for most substrates. Tests should be done to determine a spread rate to avoid applying ECOFINISH at a rate that will make the surface slippery.
NOTE : It is not recommended to apply ECO-FINISH by roller as there is a tendency to create air bubbles in the coating by too vigorous rolling; and over rolling on partially dried coating. It is best to apply ECO-FINISH by Tee Bar Pad applicator, soft hair broom, brush or airless spray.
ECO-FINISH needs to be applied in thin even coats laying off as application. Thick coats cause drying problems with ECO-FINISH sometimes leaving an opalescent(whitish) film - not a clear film. Substantial water contact within a week or so after application may create a very light whitish spot effect in the film. The effect disappears when the water is removed or evaporated and will not occur when the film gains full strength. Rising moisture in substrates needs to be constrained before application of ECO-FINISH. Keep ECO-FINISH off window, door frames and glass.
Clean up wet ECO-FINISH deposits with water and dry ECO-FINISH deposits with MARCMOVE.
Store ECO-FINISH in sealed containers under cover in a cool area away from foodstuffs.
ECO-FINISH is sold in packs of 20 and 200 litres.
ECO-FINISH is not a hazardous product for transport under the guidelines of WORKSAFE