Wrimco two parts Epoxy is a water based, epoxy waterproof membrane. It is a high performance, versatile, two-part, water based, hydrostatic pressure resistant, waterproofing barrier membrane coating suitable for most types of porous and semi-porous surfaces including green (newly laid) hardened concrete and damp surfaces. It cures to form a strong, waterproof, hydrostatic pressure resistant and water vapour pressure barrier and is formulated for application on to damp, newly laid concrete and most other construction surfaces. It is suitable for potable (drinking water) applications and can withstand up to 25 metre head of water pressure. It's versatility makes it also ideal as a primer for waterproofing membranes, paints, industrial coatings and as a bridging coating for normally incompatible coatings. It's standard colour is light grey but is also available in off-white and black (minimum quantities apply). It has very low VOCs and meets the 'Green Star' enviromental criteria.
Ardex WPM 300
ARDEX WPM 300 (HydrEpoxy 300) is a two component water
based epoxy polyamide membrane/barrier coating. Approved for use with potable
(drinking) water, independent testing confirms conformity with the requirements
of AS4020.2000 and BS6920. As a low water vapour transmission coating in the
building and construction industries and as a barrier/seal coating over freshly
laid or damp concrete. As a hydrostatic pressure resistant waterproofing
membrane to prevent water seepage or dampness penetration through to the
interior of walls and floors. As a waterproofing barrier on the negative side
in below grade surfaces such as basements, tunnels, lift wells, retaining walls
and car parks. As a waterproofing membrane or barrier coating over freshly
laid hardened (green) concrete, prior to the application of conventional
levelling compounds, carpet and tile adhesives. As a waterproofing membrane in
tanking applications, including potable water containment.
As a barrier seal coating over damp, green or
efflorescence producing concrete prior to over-coating with conventional
ANTIROCK PRIMER is a blend of SBS modified bitumen,
fast-evaporating solvents and adhesive enhancing additives. It is used to prime
concrete and metal surfaces on civil engineering structures in order to improve
the adhesion of torch-applied ANTIROCK waterproofing membranes. APPLICATION
ANTIROCK PRIMER can be applied with a brush or roller on clean, dry substrates
free of any residue that may hinder adherence. Shake well before using. It must
be thoroughly dry before applying the waterproofing membrane. Drying time will
vary depending on air and surface temperature and humidity. WARNING: Do not
accelerate drying of ANTIROCK PRIMER by heating with a torch. Average coverage:
0.15 to 0.25 L/m2. RESTRICTION ANTIROCK PRIMER is a highly flammable product.
Store away from direct sunlight and open flame. Keep ignition sources away
during application and until solvent has evaporated. Harmful if inhaled,
swallowed or when in contact with the skin. In closed areas, ventilate
carefully using mechanical means if necessary. Do not pour residues in drains.
system ECO PREP N PRIME is a unique, solvent free, flexible primer
specifically designed with enhanced adhesion properties for use onto
metallic, smooth, dense and non-porous surfaces. ECO PREP N PRIME is a
safe alternative to hazardous solvent-based primers and etching products,
to enable and improve the adhesion of a wide range of coatings,
waterproofing membranes and tile adhesives over non-absorbent surfaces.Priming over galvanised iron, zincalume,
stainless steel, copper, brass and most metals. Priming over glazed tiles to
enable re-tiling without etching or grinding. Priming over vinyl tiles and
laminates. Priming over acrylic and oil-based painted surfaces. Priming over
dense concrete. Priming over PVC and rigid plastics. Priming over epoxy
coatings. Priming general non-porous and shiny surfaces
is a two component water based epoxy coating used to prime seal, coat concrete and masonry surfaces. It cures to a tough chemical and water resistant coating having excellent adhesion to sound concrete.Packaging: 20 litre, 4 litre.
Water based, user friendly.
Excellent water resistance.
Excellent oil resistance.
Excellent adhesion to fresh concrete.
Applicable to damp surfaces.
Resists hydrostatic pressure when cured.
Requires a UV resistant top coat when in direct sunlight.
Sikafloor 160 Epoxy Primer
A three-component, high solids epoxy floor resurfacer.
This product can be applied using a screed and finished by hand troweling or
power troweling. Typical thickness is from 3/16" (4.8 mm) to 1/4" (6 mm). Designed for overlaying new and resurfacing worn concrete
floors in light to heavy duty industrial applications. Sikafloor 160 is
formulated to restore and protect concrete floors from impact and abrasive
For wet in wet application: Prime with either
Sikafloor 160 or Sikafloor 161 using a squeegee and back roll to provide
uniform coverage. Avoid ponding. If primer becomes tack-free, re-prime the
substrate. For application over cured primer: Apply either Sikafloor 160 or
Sikafloor 161 using a squeegee and back roll to provide uniform coverage and
broadcast a 20 mesh quartz sand into the fresh primer. Avoid ponding
TREMproof 200 EC is a two part waterborne epoxy coating system designed to act as a moisture and vapour barrier primarily over cementitious substrates. TREMproof 200EC is a minimum two-coat system. The coverage rate as specified must be achieved to ensure transmission barrier and low permeability is obtained. Applying with a brush or roller, ensure to work the material into the substrate surface to fill voids and eliminate pinholing. Successive coats should be applied at right angles to the previous coat. It is recommended that as application progresses, the coating depth be tested at random points with a wet film gauge/ comb. Extreme care is necessary, and if required, protection should be provided to ensure TREMproof 200EC is not damaged in any way between or after final coating.
Duroprime SSP is a solvent
free primer specifically developed with adhesion enhancing properties on
metals, non-porous, dense and smooth substrates. It is designed for use on both
vertical and horizontal surfaces, achieving high adhesion without the need for
etching or using solvents. Ideally suited for the application of Duroprime SSP
membrane coatings, adhesives and mortars to enable ease of bond to difficult
free alternative to dangerous solvent based primers. Bonds to a variety of
metal, plastic, glazed, smooth & dense surface. Super adhesion properties. Ease
of application. Very low dirt retention, non-tacky. Suitable for internal and external applications. Can be directly covered
over with Duroprime SSP membranes or enhanced adhesives and mortars. Time
saving, user friendly and environmentally safe
DUROPRIME PU PRIMER is a moisture curing, single pack, liquid
polyurethane penetrating waterproofing primer. It is formulated to compliment
DURPROOF. Cross - link technology the chemical bond between the PU, Durorproof
PUM or DUROPRIME is exceptionally strong. PU as a primer Improves the adhesion
and preformance of the membrane 'locks - down' dust and loose materials
improves the spreading and application of the subsequent membranes, provides a
penetrative secondary waterproof barrier and improves the coverage of the
DUROPROOF PUM and DUROPRIME membranes. DUROPRIME PU PRIMER is a penetrative
sealer and provides a penetrative waterproof barrier when applied in 2 coats or
more. DO NOT use as a primary waterproofing membrane . Use only in conjunction
with DUROPROOF PUM waterproofing membranes . The PU dries by evapouration of
the solvent and then cures upon contact with water vapour in the air. It incorporates cross- linking technology to enhance adhesion and
provides a strong bond to the substrate. Enhances the overall performance and
functionality of the waterproofing membrane. Easy to apply - single pack. Dries
quickly, with large top coating window. Has good strength, elasticity and
penetrative qualities. Moisture curing polyurethane. Suitable for above ground
and below ground applications. Improves the coverage of the DUROPROOF PUM
membrane. Improves easy of membrane application. Suitable for permanent
immersion of water. Suitable for use on most porous substrates
TREMprime Non-Porous Primer
TREMprime Non-Porous Primer is a quick-drying, one-part
white specially formulated to enhance adhesion between various non-porous
materials and Vulkem products. Basic Uses: Is an adhesion promoter used to
improve the bonding of Vulkem one and two-part urethane sealants and Vulkem
urethane waterproofing membranes to substrates, such as, mild to stainless
steels, anodized and milled aluminium, high performance paints, glass, PVC,
polyesters and other non-porous surfaces. TREMprime Non-Porous Primer may also be used to prime
stand pipes and drains if necessary, prior to detailing with Vulkem
Sikafloor 161 two parts Epoxy
161 is a two part, epoxy resin use for priming. Sikafloor 161 is designed as a
primer for Sikafloor epoxy and urethane coatings, as well as for broadcast and
primer by squeegee at the rate of 160 - 266 ft2 / US gal (3.4 - 6.5 m2 / L) at
6 - 10 mils (0.15 - 0.25 mm) wet film thickness (w.f.t.) and back roll with
pressure after 15 minutes. Coverage will vary depending on the porosity of the
prepared floor. Product has a limited Pot Life, see Typical Data. Do not apply
by dipping roller into mixing container. Pour a bead of product in the form of
a ribbon on the surface to be coated, then spread with squeegee and back roll.
Ensure that the coating is pore-free and pinhole-free and provides uniform and
complete coverage over the entire concrete substrate. If necessary, apply an
additional coat to ensure the coating is pore-free and pinhole-free and
provides uniform and complete coverage over the entire concrete substrate.