Wrimco Waterproofing                              Home  | Specification | Product | Project | Technical data A-Z | Contact us

Adhesive Membrane

Anti-root Membrane

Approved Applicators

Backing Rod

Drainage Cell

Drainage Sheet

Epoxy Adhesive

Epoxy Flooring

Flat Roof Membrane  

Foundation Membrane

Liquid Membrane

Membrane Protection

Product Application

Product Category

Retaining Wall

SBS Sheet Membrane

Torch on Membrane

Under Slab Membrane

Vapour Barriers

Waterproofing Primer

 

Waterproof Balcony Liquid Membrane Waterproof Bathroom liquid membrane Waterproof Retaining Wall Liquid Rubber Membrane How to waterproof a bathroom Waterproof Internal Wet Area Membrane Waterproof Tiled Balcony Clear Penetrating Sealer Trafficable liquid membrane UV Protection liquid membrane Waterproof Water Feature liquid membrane Hydro Pressure Resistant liquid membrane Waterproof fish pond liquid membrane waterproof bathroom liquid membrane Waterproof above screed liquid membrane UV Resistant Polyurethane Membrane Waterproof leaking balcony liquid membrane waterproof damp basement wall liquid membrane Solutions to common waterproofing problems Maxseal Foundation Polyurethane Membrane MasterSeal M210TIX Latex Rubber Liquid Membrane Waterproof wet basement wall liquid membrane Injection Drill Pump Vulkem 350/345/346 Ardex WPM 300 Epoxy - Stop Rising Damp Waterproof Metal Roof Liquid Membrane Repair Leaking Balcony, Flat Roof, Planter Box, Bathroom Waterproofer, waterproof Leaking Balcony, Flat Roof, Planter Box, Bathroom tradesman, handyman Waterproof Box gutter liquid membrane Waterproof Retaining Wall liquid membrane Waterproof Internal, External Wall Liquid Membrane Waterproof Concrete Slab Liquid Membrane Waterproof Balcony Liquid Membrane Stop Leaking Shower Liquid Membrane How to waterproof a retaining wall How to waterproof a Retaining Wall How to fix leaking fish pond Waterproof Garage Roof Liquid Rubber Membrane Waterproof water tanks for drinkable water Waterproof Leaking Roof, Gutters, Balcony, Car Park tradesman Waterproof leaking box gutters tradesman Repair Leaking Balcony, Flat Roof, Planter Box, Bathroom Waterproofer   Repair Leaking Balcony, Flat Roof, Planter Box, Bathroom Waterproofer   HiBuild Hydrastatic Water based Epoxy Hydrostatic Negative Pressure Water Based Epoxy Under tile screed bed waterproofing membrane Prevent and Fix Rising Damp Waterproofing Epoxy Waterproof exposed balcony liquid membrane Repair leaking balcony waterproof liquid membrane Waterproof Bathroom Liquid Membrane Planter Box Retaining Wall Tanking Liquid Membrane Waterproof Leaking Metal Roof Waterproofer HOw to repair leaking fish pond Waterproof Underground wall Liquid Membrane Waterproof Planter Box liquid membrane Waterproof Watertanks Cementitious Liquid Membrane Waterproof Lift Pit Liquid Membrane ARDEX WPM 001 - Undertile Waterproofing Membrane Waterproof Planter Box Root Resistant Liquid Membrane Repair Bitumen Roof Waterproofing Liquid Membrane UV Protective Polyurethane Membrane Waterproof External Brick Wall liquid membrane Waterproof Retaining Wall Liquid Membrane Waterproof Planter Box Liquid Membrane Waterproof Wet Retaining Wall Liquid Membrane Waterproof Leaking External Wall Licensed Waterproofer Emer Clad Acrylic Liquid Membrane Waterproof Planter Box, Retaining wall liquid membrane Fast Cure Elastomeric Waterproofing Membrane Systems Waterproof Leaking Swimming pool tradesman UV Resistant Acrylic Liquid Membrane How to Waterproof a Leaking Metal Box Gutter Sikalastic 560 - Repair Bitumen membrane Roof Waterproof Lift Pits Tradesmen Waterproof Leaking Kitchen Tradesmen Waterproof Leaking Internal Basement Walls tradesman Waterproof Leaking Laundry tradesman Waterproof Leaking Deck, Verandah Tradesman Waterproof Leaking Roof, Gutters, Balcony, Car Park Tradesman, waterproofer, license waterproofer Repair Bitumen Roof Liquid Rubber Membrane Waterproof Besser Block Wall with Liquid Membrane Waterproof leaking bitumen roof contractors Waterproof leaking bitumen roof contractors  Waterproof Leaking Retaining Wall, Basement Wall Tradesmen Waterproof Leaking Ceiling Waterproofer Repair leaking Water Tank licensed Waterproofer Repair Leaking Fire Water Tank Licensed Waterproofer
Commercial Building Sheet Membrane Concrete Roof Sheet Membrane Waterproof Deck Sheet Membrane Entertainment building Waterproofing Membrane Waterproof Government Building Sheet Membrane Waterproof Hospital Building Sheet Membrane Waterproof Landmark Building Bitumen Membrane Waterproofing Planter Box Sheet Membrane Waterproof Plywood Roof Sheet Membrane Waterproof Residential Building Sheet Membrane Waterproof Roof Bitumen Sheet Membrane Waterproof Flat Roof Sheet Membrane Waterproof Retaining Wall Sheet Membrane Terrace waterproofing Sheet Membrane Waterproof University Building Sheet Membrane Wrimco Reference Waterproof Lift Pit Sheet Membrane Waterproof Concrete Roof Sheet Membrane Tanking Sheet Membrane Systems Vaucluse Waterproofing Project  Mosman Waterproofing Project Waterproofing Palm Beach Waterproofing Dover Height Waterproofing Darling Point Waterproofing Bellevue Hill waterproofing tradesman Knowledge Base FAQ Waterproofing Product Waterproof Leaking Garage Roof tradesman Repair SBS, APP Sheet Membrane Waterproof Concrete Slab Sheet Membrane Waterproof Leaking Garage Roof Liquid Rubber Membrane Waterproof Leaking Metal Roof Liquid Rubber Membrane Waterproof Balustrade Sheet Membrane Waterproof Commercial Building Project Bitumen Sheet Membrane Closed Cell Backing Rod Repair Crack Joints Closed cell backer rod Expansion joint backing rod Backing Rod Waterproof Leaking Roof, Balcony, Box Gutter tradesman Repair Leaking underground basement wall Waterproofer Waterproof Leaking Shower, Bathroom, Wet area Tradesman Repair Leaking Deck, Planter Box Waterproofer Waterproof Leaking Fish Pond Tradesman Waterproof Rising Damp Basement Tradesmen Roofs Waterproofed with Wrimco Sheet Membrane Waterproof Retaining walls with sheet membrane Waterproof Balcony with Sheet Membrane HDPE Self Adhesive Sheet Membrane Waterproof Commercial High Rise Building Roof Contractors Waterproof Car Park Roof with sheet membrane Ardex WPM 116 Sheet Membrane Ardex WPM 150 APP Sheet Membrane ARDEX WPM 188 SBS Garden Tanking Membrane ARDEX WPM 185 APP Sheet Membrane Ardex WPM320 Retaining Wall Sheet Membrane Waterproof Deck with torch applied Sheet Membrane ARDEX WPM612 FL TPO Fleece-Backed Roof Membrane TREMproof SBS 4000M Mineral Bituminous Membrane ARDEX WPM 1000 Weldable Waterproofing Membrane SBS Sheet Membrane Installation ARDEX WPM 3000X peel and stick membrane ARDEX WPM 750 Undertile Butynol  Waterproof Concrete Slab with Sheet Membrane ARDEX WPM 444 APP Sheet Membrane How to waterproof a Retaining wall How to waterproof a Planter Box How to waterproof a planter box How to waterproof Tiled Balcony with clear sealer How to waterproof a Shower  Ardex SRO 834 Waterproofing Specification Wrimco Sheet Membrane Waterproof elevator pits Sheet Membrane SBS Sheet Waterproofing Membrane How to waterproof balcony with sheet membrane Anti Root Sheet Membrane Vehicular Traffic Liquid Membrane Waterproof Planter Box with torch applied sheet membrane Waterproof Balconies Decks Podiums Prevent Rising Damp Hydro Static Epoxy How to waterproof a planter box 

Trafficable Liquid Membrane :

    

Description  

Azcoflex TR is a trafficable, high build, water based acrylic waterproofing membrane primarily designed for use in areas of infrequent to moderate foot traffic. Azcoflex TR is UV resistant, tough and durable but still flexible. When cured it gives a seamless waterproofing membrane with excellent water ponding resistance, low dirt pick- up and good thermal shock stability. Although the tough polymer system provides an excellent trafficable waterproof membrane, it can also be used on walls. It is a complete protective waterproof barrier for severe weather conditions, wind driven rain, salt spray and UV exposure. 

Azcoflex TR has very low VOCs and meets the 'Green Star' environmental criteria.

Uses:

Azcoflex TR (TR is for trafficable) is designed to provide a pedestrian trafficable waterproofing membrane for the use on: 

Roofs, decks, terraces, podiums and balconies.
Walls, parapets and facades. 
 

Suitable Surfaces:  

Azcoflex TR can be used over a wide range of properly prepared and primed substrates including:

Concrete, cement, cement render, block work, brick, masonry, FC and CFC sheeting, timber.  

Specification:  

The information contained in this product data sheet is typical but does not constitute a full specification as conditions and specific requirements may vary from project to project. The instructions should be considered as a minimum requirement but the applicator or contractor must use their skill, knowledge and experience to carry out additional works as may be necessary to meet the requirements of the project. Specification for specific projects should be sought from the Company in writing.  

Limitations:  

The Azcoflex TR is designed to withstand normal, occasional to moderate broad soled foot wear traffic. Azcoflex TR can be damaged by point loads, sharp edges, scuffing and scraping and should be protected from this.
It is important that large cracks and joints be independently waterproofed as described under Detailing Preparation.
 

Benefits and Advantages:  

Azcoflex TR is both a waterproofing membrane and a trafficable coating.
Water-based.
Very low VOCs and meets the 'Green Star' environmental criteria.
User and environmentally friendly.
Can be tinted.
Provides a tough, trafficable membrane.
UV Resistant, suitable for exposed areas.
Water ponding resistant.
Low dirt pick-up - can be cleaned.
Can be readily repaired or over-coated, if required.
Can be used with a reinforcing fabric.
 

Precautions in Use

Product is considered low risk if used properly as intended. Whilst Azcoflex TR is a user friendly product it is recommended that all safety precautions are followed as per product label and data sheet. In exposed areas, do not apply if rain is imminent and protect membrane from rain and inclement weather until fully cured.

Priming and Surface Preparation

Good preparation is essential. Surfaces must be sound, stable, dry, clean and free of dust, loose, flaking, friable material and substances that may diminish adhesion.  

Priming
Surfaces should be suitably primed with Primeseal applied at no less than 1 Lt per 4m2 and allowed to dry. Primeseal must be used for roof and exposed areas, timber and particle board surfaces, bitumen or where there is a risk of entrapped moisture in the substrate which may cause the membrane to bubble.
Alternative primers such as Azcoseal or Maxiprime may be used in non-exposed areas and where the moisture content of the surface is very low applied at no less than 1 Lt per 4m2.
Excessively porous, friable and dusty surfaces may require an additional priming coat.

Please refer to the product data sheets of the stated primers.  

Detailing Preparation

Corners
Prime as required.
Apply an adequate flexible polyurethane sealant, in accordance the manufacture's instruction and tool off to form a solid, coved 45 degree fillet extending at least 10mm on to the adjacent surfaces. Apply the membrane directly over the sealant and on the adjacent surfaces.
For Additional waterproofing protection the following additional steps should be taken
Lay a strip of Leak-Seal Tape (stick-stick, butyl mastic waterproofing membrane with a polyester backed reinforcing fabric) over the cured polyurethane sealant (as described above) pressing it firmly on the surface. Apply the Azcoflex TR membrane directly over the tape and on the adjacent surfaces.

Joins, gaps and Cracks
General

Joins, gaps and cracks should be suitably filled and sealed with an appropriate elastomeric sealant, preferably a polyurethane sealant, and allowed to cure. 
Recommendation: The movement of small cracks should not be underestimated and should be at least covered with a flexible polyurethane sealant or additional coats of membrane.

Large or Live Cracks
Large cracks should be routed out to form a 'V' and then filled and sealed with a polyurethane waterproof joint sealant as per the manufacturer's instructions. The sealant should be finished slightly proud of the surface and allowed to cure. 
After priming, as required, lay a strip of Leak-Seal Tape over the join or crack pressing it firmly on to the substrate. The membrane is then applied directly to the Leak-Seal Tape and extending at least 75mm on to the adjacent surfaces.

If the Leak-Seal is not used then a suitable bond breaker tape (such as duct tape) at least 48mm wide should be laid over the join or crack and apply a fully reinforced membrane consisting of a base coat of Azcoflex TR membrane in to which the reinforcing fabric is embedded, a saturating coat of the membrane ensuring that the fabric is entirely saturated and covered and then allowed to cure.  At least one or two further coats are applied as per the membrane's Product Data Sheet extending at least 75mm on to the adjacent surfaces.  

Joins - Particularly in CFC Sheeting and Timber Sheeting
Ideally the sides of the sheets should be fully coated with a flexible polyurethane waterproof joint sealant prior to butting the sheets together.
If not, the joins should be suitably filled and sealed with an appropriate elastomeric polyurethane waterproof sealant and finished flush with or preferably slightly proud of the surface and allowed to cure. 
After priming, as required, lay a strip of Leak-Seal Tape over the join, pressing it firmly on to the substrate. The membrane is then applied as described under 'Large or Live Cracks'.

If the Leak-Seal is not used then follow the procedure as described under 'Large or Live Cracks'.

Waste Outlets, Penetrations and Angles
Waste Outlets: Floor wastes and puddle flanges should be rebated in to the floor to allow water to readily drain and its perimeter edges and gaps sealed with a polyurethane sealant.
Plastic or metal angles: Where required by the Building Code such as internal hobs and exterior door barriers and also plastic corner angels under wall boards, should be securely embedded in to a continuous, gap free bed of a polyurethane sealant / mastic.

Application

Application can be with brush, spray or roller. Where exposed to the elements, do not apply membrane if rain is imminent and protect the membrane from water and damage until it has fully cured.

MEMBRANE APPLICATION
Floor System:

1st & Saturating Coat (done in one step).
Apply a first coat of Azcoflex TR using brush, roller or spray over the prepared and primed surface at the rate of 0.5 Lt sq.m. Embed fibreglass matting or Durascrim reinforcing fabric into the wet membrane. The reinforcing must be well worked into the wet membrane to eliminate trapped air and wrinkles. Immediately apply a saturating coat at the rate of 0.5 litres per sq.m. ensuring the the fabric is entirely embedded and covered. Allow to cure. Inspect the cured surface and cut out and replace any trapped air bubbles before proceeding. The surface should be smooth with a regular profile from the embedded reinforcing and free of bubbles, wrinkles or surface defects. Allow to dry.
2nd Coat.
Apply a second coat of Azcoflex TR by brush, roller or spray at the rate of 1.0 Lt per sq.m. Allow to cure.
3rd Coat.
There are occasions when the use of a third application might be considered necessary. Typically this should be considered in coastal/marine environments or where excessive pedestrian traffic is anticipated. Application will be at the rate of 0.5 litres per sq.m.

The minimum dry film thickness of the membrane should be at least 1.5mm.

Wall System:
Apply two coats of Azcoflex TR at the rate of 2m2 to 3 m2 per Lt per coat. The minimum dry film thickness should be at least 500 microns. The crack bridging properties of the coating is dependent upon the cured thickness (the thicker the membrane the more it will flex) and additional coats may be required over doubtful areas.

Coverage

The stated average coverage rate may vary depending upon type, condition, porosity, texture of the surface and application technique.  

Reinforced: The total combined use of Azcoflex TR should be a minimum of 2 Lt per m2.
Unreinforced: The total combined use of Azcoflex TR should be at least 1.5 Lts per m2
Walls: The total combined use of Azcoflex TR should be at least 1.0 Lt per m2.

Colours

Azcoflex TR can be tinted to a wide variety of Light colours.

Drying and Curing

Drying and curing of the product is affected by type, dryness and porosity of the surface, temperature, humidity, ventilation, climate conditions and application technique and therefore drying and curing can only be given as a guide.  

At 25 o C and 50% RH (per coat):
Touch dry: 2 to 6 hours.
Dry:           6 to 12 hours. 
Full cure:   24 to 36 hours.
Service Temperature: 10
o C to 50 o
Application Temperature: 10
o C to 30 o C

Storage

Azcoflex TR should be stored in a cool dry place. Keep out of the reach of children. Do not allow the product to freeze. Suitable containers: Plastic pails as recommended by the manufacturer.

Clean Up

All tools and equipment should be cleaned in water as soon after completion as practical.

Tiling, Topping or Top Coating

Usually the product is left exposed.

Safety & Precautions

Azcoflex TR is a user friendly and safe to use if used correctly as intended. The use of rubber gloves and eye protection is recommended. Observe the safety precautions on the pail, data sheet and Material safety Data Sheet.  

For full safety data refer to the products Material Safety Data Sheet. Observe precautions as per label.

Tests and Technical Data

Shelf Life: Up to 12 months in unopened containers and 6 months after resealing open pails. The above data is based on 25 o C and 50% RH. Performance and shelf life can vary when stored in extreme conditions. Azcoflex TR is available in 4 and 15 Lt pails.   

Service Temperature: 5 o C to 50 o C

Application Temperature: 10 o C to 35 o C .

 

Waterproofing FAQ

Membrane Protection Board

Waterproofing Coating

Waterproof Drainage Sheet

Waterproofing Primer

Repair and Maintenance