Duromastic
P15 Diamond is a polyurethane modified copolymer acrylic waterproofing membrane
specifically formulated for bathrooms, laundries, balconies, terraces and other
wet areas. Use Duromastic P15 Diamond prior to installing mortar beds, render
or tiling. The membrane forms a grey coloured water resistant elastomeric film
with excellent durability. Application:
Do not apply externally if
rain is expected presently. Do not apply below 100oC or above 300oC externally.
Ensure that the primer coat is completely dry. Apply evenly and check for
missed areas and pin-holes. Apply further coats from cross directions after 4
to 6 hours. Do not apply as one coat. Apply down into drainage outlets. Use
reinforcing fabric over expansion joints, cracks, all wall and floor junctions,
and pipe penetrations. Apply this by first brushing out a layer of membrane
(1-2 mm), next lay in the fabric and ensure there are no air bubbles, and the fabric
is fully set in without wrinkles. Then brush over with more membrane. Good air
flow and warmth will speed drying.
Sikalastic 488/488SL is a high performance, hand-applied, low VOC, moisture curing
single-pack elastomeric polyurethane waterproofing membrane. Sikalastic -
488/488SL is directly foot-trafficable. It is designed for waterproofing
diverse parts of a building including: Balconies Terraces Podium decks
Bathrooms and wet areas Plant room floors Inverted roofs Under tile beds. UV
resistance Seamless membrane High resistance to puncture and standing water
Quick tack-free surface Low VOC High elongation, class III membrane according
to AS/NZS 4858 Crack bridging capability, no reinforcement needed Elastomeric
behaviour Single pack, ready to use Available in various colours
Sikalastic 590
Sikalastic-590
is one component polyurethane, acrylic dispersion with improved water ponding
resistance, excellent UV resistance, good crack bridging capacity and great
aesthetics. For manual/spray application, Sikalastic-590can be applied as
coating ora reinforced liquid applied membranewithSika-120Reemat. USES: For waterproofing
solutions in both new construction and refurbishment projects. For roofs with
many details and complex geometry when accessibility is limited. For cost
efficient life cycle extension of failing roofs. For reflective coating to
enhance energy efficiency by reducing cooling costs(Sikalastic-590White).Advantages:
Good behavior under limited water ponding. UV resistant and resistant to
yellowing and weathering. Highly elastic and crack-bridging. Non-toxic and VOC
compliant water based coating. One component-ready to use. Excellent adhesion
on porous and non-porous substrates. Seamless waterproofing membrane. Water
vapour permeable.
Protection of concrete surfaces according to EN 1504-9,
principles 1: protection against penetration (coating); 2: control of moisture
(coatings); and 8 increasing resistivity (coating).
Waterproof protection of concrete structures including
tanks, basins, pipes, etc.
Waterproofing external wall surfaces to be backfilled in
ground.
Internal waterproofing of walls and floors, in basements.
Waterproofing of terraces and balconies over concrete or
prepared existing tiles.
Flexible protection coating for reinforced concrete
structures against the effects of de-icing salts, freeze-thaw and carbon
dioxide swell consolidation. Waterproof Planter Box Membrane
Duromastic PU -
For Planter Boxes, Retaining walls and Tanking
It is
a liquid applied, modified polyurethane elastomeric waterproofing
membrane which when fully cured forms a permanently flexible waterproof
lining to most building surfaces including reinforced concrete, block
work, brick work, cement render, plaster board and fibre-reinforced
cement.
Duromastic P15
DuroP15 membrane is a cross-linking waterborne,
high solid content polyurethane membrane. Formulated to provide a membrane with
tenacious bond to most surfaces, it is a tough flexible waterproof
membrane with a high film strength, that will expand and contract with normal
substrate movement. It is supplied as a thixotropic liquid, which is easily
applied to both vertical and horizontal surfaces. The formulation is fully
optimised to ensure quick tack free time, fast cure, excellent chemical
resistance and passes the bleach and immersion test requirements of
AS:4858-2004. Use areas: Internal Wet Areas and Shower Recesses, External
Balconies and Decks, Tanking, Roofs - topcoat with Duro AC (UV coating),
Water Features
Dampfix Gold
One part, highly elastic, Class 3, water-based polyurethane waterproofing membrane system that meets the requirements of AS3740 by complying with AS/NZ 4858.
The Bostik Dampfix Gold waterproofing membrane system is specifically formulated for application on graded substrates that provide positive falls to drainage outlets. Overlaying tiling systems must comply with Guide to the Installation of Ceramic Tiles - AS3958.1). This is a 2-coat system applied over primed porous & nonporous substrates. It is not recommended as a membrane system in immersed applications (such as pools or spas)
Duraroof
Duraroof is a liquid membrane product based on a unique double crosslinked copolymer system. It does not contain plasticisers or oils that can leach, degrade or contribute to dirt-pickup. Duraroof is used as a fully exposed membrane or beneath a tiled mortar bed. It can withstand occasional light foot traffic. The product is water-based yet offers strong resistance to water ponding. The cured membrane has exceptional flex and elasticity for good crack bridging properties while at the same time maintaining good tensile film strength. Duraroof has excellent resistance to UV, colour fade and chalking. Duraroof membrane is easily maintained, recoated and repaired .The water content is low which enables fast drying, and thick films to be built up quickly. The product is supplied as a thixotropic liquid, which is easily applied to both vertical and horizontal surfaces. It complies fully with the test requirements of AS:4858-2004 "Wet Area Membranes" and passes at Class III, the highest level in the Australian standard
Dampfix PU
One component, highly elastic, class 3, polyurethane waterproofing membrane system that contains no bitumen and complies with AS/NZ 4858.
Dampfix PU
polyurethane waterproofing membrane is specifically formulated for applications where the waterproofing membrane is to be covered by tiling systems laid on an unbonded reinforced screed to falls (ref: Guide to the Installation of Ceramic Tiles - AS3958.1).
This is a 2-coat system applied over primed porous & non-porous substrates. It is not recommended as a membrane system in immersed areas (such as pools or spas).
Duromastic AC
- for roofs, walls, fascias, balconies
is a waterproof and UV resistant liquid membrane used for long-term waterproofing and decorative coating of building surfaces. It is applied by brush, roller or spray and cures to form a permanently flexible waterproof membrane that is resistant to weathering for many years. Although the membrane is waterproof it allows the substrate to breathe.
Tremproof 90
TREMproof 90
is a two part liquid applied co-polymer membrane with fibrous
reinforcement. TREMproof 90 cures rapidly to form a flexible
waterproofing lining for showers and other wet areas as described in the
Australian Standard waterproofing wet areas within residential
buildings. TREMproof 90 forms a waterproofing lining to most building
materials including reinforced concrete, cement render, water resistant
plaster board, and fibre reinforced cement sheet flooring. etc. The
surface must be firmly fixed to manufacturers direction. Clean and dry.
TREMproof 90 is suitable to external use on light pedestrian trafficable
decks, parapets and flashings.
Drizoro Maxseal Flex M
Drizoro Maxseal Flex-M a one-component cement-based
mortar. Once mixed only with water, it provides a high-performance flexible
coating, for waterproofing and protection of concrete against positive and
negative pressure. Waterproofing and protection of water retaining structures,
such as potable water tanks, reservoirs, dams, water channels, fountains and
swimming pools. below-grade structures like basements, retaining walls,
foundations, tunnels, galleries subject to high negative water pressure. concrete
and masonry in wastewater treatment plants, settlement tanks. against
carbonation, and marine environments, such as civil works, bridges, architectural
buildings, residential facades. masonry and concrete against soil salts and
aggressive ground water, in underground jobs, foundations, etc. roofs,
terraces, balconies. window boxes, gardens and other surfaces subject to root
penetration. Internal waterproofing of bathrooms, kitchens and other wet areas
in hotels, hospitals, offices, residential buildings. Provides
a fully-flexible coating which ensures complete waterproofing even in
the most severe conditions, or high negative water pressure. Good crack-bridging
capability (> 0,5 mm). Acts as an anti-fracture membrane between the
substrate and other finishing coats if applied. Provides an excellent barrier
effect against Carbon Dioxide (CO2) and chlorine (Cl-), thereby prevents
carbonation and corrosion of steel rebars. Allows water vapour diffusion and
the breath ability of the concrete. Resistant to abrasion and UV rays. Withstands
atmospheric pollution, corrosive effects of salt water or de-icing salts. Excellent
adhesion. Do not require primer and must be applied on wet surfaces. Non-toxic, suitable for contact with potable water. Longer
lasting that other coatings, thus reducing maintenance costs. Environmentally
friendly and suitable for application in poor ventilation areas. Withstands root penetration.
Mapegum WPS
Quick-drying
flexible liquid membrane for waterproofing internal surfaces. Waterproofing
indoor floor and wall surfaces that are not subject to rising damp nor in
permanent water immersion. Flexible, anti-fracture membrane. Apply before the
installation of ceramic tiles or stone material. Mapegum WPS may be used
on the following: plasterboard, gypsum or cementitious render, lightweight
cement block and marine-plywood; cementitious, anhydrite, wooden and magnesite
substrates and existing ceramic and natural stone after the application of Eco
Prim T primer. Product certified EC1 Plus by the GEV Institute
(Gemeinschaft Emissions-kontrollierte Verlegewerkstoffe e.V) as a product with very
low emission of volatile organic compounds. Ready to use. Rapid application. Floor
coverings may be installed after 12 hours. Excellent elongation properties. No
reinforcement required. Some application examples. Waterproofing walls and
floors in bathrooms and shower cubicles before laying ceramic tiles, natural
stone and mosaic. Waterproofing kitchen walls and floors, and work tops before
laying ceramic tiles and natural stone.
Tremproof 100
TREMproof 100 (DEXX) is a heavy bodied liquid applied acrylic membrane waterproofing system.Excellent UV resistance. Trafficable - excellent abrasion resistance. Suits a wide range of substrates. System enhancement through a range of primers and top coats to optimise performance. Excellent adhesion. Wide range of colours. For new construction or refurbishments. Water based, easy clean up. Ready to use, no mixing required.
Waterproofing of; Exposed roofs. Walkways-Requires double reinforcement, see Usage Guidelines. Parking decks with light vehicle traffic. Requires double reinforcement Parapet walls. Plant/mechanical rooms and floors. Internal wet areas.
Balconies. Decks. Requires double reinforcement
Duroproof PPM
- Single component polyurea and polyurethane membrane
Duro PPM is a high quality, superior performance single component liquid that cures to rapidly to form a polyurea / polyurethane hybrid membrane that is tack-free, high modulus, tough, flexible and suitable for exterior use.
Single component, easy to spread. Combines high elongation and tensile strength for excellent toughness. Low odour, low VOC & complies with Green Star requirements.Trafficable and tack-free overnight cure. Good abrasion and tear resistance. Good resistance to weathering. Class III - elongation as per AS/NZ 4858. High build application is possible.
Duromastic BLW
is a liquid applied, latex modified bituminous elastomeric waterproofing membrane which, when fully cured, forms a permanently flexible waterproof lining to most building surfaces including reinforced concrete, block work, brick work and cement render.
Package: 20 litres, 10 litres, 4 litres.
Concrete must be cured for a minimum of 28 days and render 7 days. Remove dirt, dust, loose particles, oil and unsound concrete etc. Water blast if necessary. Surface must be dry. Fill holes and open joints in block work or concrete prior to application of membrane.
Dampfix 3
A 2-Part,
water-based, Acrylic modified cement, Class 2 waterproofing membrane
system. This waterproofing membrane system is specifically formulated
for application on graded substrates that provide positive falls to
drainage outlets. Overlaying tiling systems must comply with Guide to
the Installation of Ceramic Tiles. Bostik Dampfix 3 is a 2-coat system,
applied over primed porous & non-porous substrates, that requires
mixing immediately prior to application. Bostik Dampfix 3 is suitable
for use in immersed applications (such as pools and spas).
Vulkem Non Exposed membrane
Vulkem Non-Exposed is a single pack elastomeric, moisture curing, high tensile strength and tough curing polyurethane membrane. It cures to form a flexible rubber membrane. Vulkem Non-Exposed Membrane may be used to apply a
seamless, monolithic waterproof membrane to concrete substrates, compressed sheeting plywood which is well anchored and primed. Simple and easy to apply by either notched trowel, roller or brush.
Vulkem 350SL
Vulkem 350-SL/351 is an attractive composite deck waterproofing system of tough-curing liquid polyurethane. It cures to form a rubber membrane surface that provides a lasting, eye-appealing, and easy to clean coating. Non-skid surface for pedestrian traffic features use of an aggregate laden top membrane for surest footing. Vulkem 350-SL/351 may be used to apply a seamless, monolithic waterproof membrane to smooth concrete, to well anchored and primed wood, and to primed metal surfaces. Simple, easy to follow procedures and use of conventional tools or optional spray permit fast, sure application.
ARDEX WPM 908
ARDEX WPM 908 is a single part acrylic urethane based trafficable membrane. It has specifically been developed for use as a hard wearing trafficable membrane on various substrates. Water based - safe to use, low odour and easy cleaning. Hard wearing - excellent abrasion resistance properties. Single component - ready to use, no mixing required. Green Star - meets the benchmark for VOC credit in the Green Building Council of Australia’s. UV resistant - suitable for exposed applications. Slip resistant - formulated to give anti-slip properties. Substrates: Concrete, renders, screeds, masonry, AAC blocks, fibre cement sheets (external grade only) pre-primed metal. Location:
Pedestrian traffic podiums, terraces, balconies, roof decks, plant room floors, swimming pools surrounds, trafficable box gutters, steps, pathways, patios
.
Tremproof 60 - is a single component, bitumen modified, moisture curing polyurethane fluid applied waterproofing membrane
Highly flexible - over 900% elongation.
No seams or laps.
Generally no priming required.
Single layer application possible.
Ready for immediate use (no mixing required).
Accommodates crack movement from 0 to 1.6mm when fully cured at 1.3mm thickness.
Withstands hydrostatic pressure of up to 4m head of water while bridging a crack of 1.5mm width.
Over 15 years proven performance.
Available in self-levelling (H) grade or rollable grade (R) for easy application.
TREMproof 60 is a single component, bitumen modified, moisture curing polyurethane fluid applied.
TREMproof 60 is a single component, bitumen modified, moisture curing polyurethane fluid applied.
Duromastic ACS-2 is a two part high solids liquid /
cement copolymer membrane with fibre reinforcement. Duromastic ACS-2 cures
rapidly to form a flexible waterproof lining for showers and other wet areas as
described in Australian Standard AS3740:2004 "Waterproofing wet areas
within residential buildings". It complies with AS4858:2004 "Wet Area
Membranes". ACS-2 is particularly suitable for applications where polymer
modified render will be applied or in conditions where other waterbased
waterproofing products have difficulty in drying due to excesive humidity and
coolness. DUROMASTIC ACS-2 forms a waterproof lining to most building materials
including reinforced concrete, cement render, water resistant plaster board,
and compressed cement sheeting etc. The surface must be fixed according to
manufacturers directions and must be clean and dry. DUROMASTIC ACS-2 is
suitable for external use on light pedestrian trafficable decks, parapets and
flashings. Top coat with Duroarmorâ„¢ for UV resistance Features: Simple application - single pack and
water based. Simple application, water based. Fast drying. Good flexibility.
Seamless, no joints or cracks. Environmentally friendly. Good resistance to
foot traffic
Tremproof Eco Nem
TREMproof Eco Nem is suitable for use for internal wet area waterproofing.
It is water based and safe to use with minimum odour. For
GreenBuilding requirement- TREMproof Eco Nem is solvent free suitable for confined areas. It also meets the benchmark for VOC's in the Green Building Councill of Australia Ratings. TREMproof Eco Nem complies with AS4858:2004 (internal membranes) as a class III Elastomeric liquid applied membrane. TREMproof Eco Nem does not require the use of reinforcing fabric. It can be used over concrete, F/C sheet, plasterboard, timber and most building materials. It can also be used above or below floor screeds.
Dampfix 2
The Dampfix 2 waterproofing membrane system is specifically formulated for application on internal wet area applications on graded substrates that provide positive falls to drainage outlets. Overlaying tiling systems must comply with Guide to the Installation of Ceramic Tiles - AS3958.1. This is a 2-coat system applied over primed porous & nonporous internal wet area substrates. It is not recommended as a membrane system in external or immersed applications
.
Tremproof 260
TREMproof 260 Spray-Applied Waterproofing membrane is a polymer-enhanced, single component, fluid applied asphalt emulsion waterproofing membrane. It is designed for roller or spray application to concrete, masonry and other structural substrates, primarily in vertical installations. Tremproof 260 has been tested to AS4020 - 2005 Testing of Products in Contact with Drinking Water and is approved for use with potable water.