Duroflex tank is a two component polymer modified cementitious coating designed for waterproofing concrete and masonry surfaces in a variety of applications. Applied by roller, brush, trowel or spray methods, once cured Duroflex tank provides a protective barrier to concrete surfaces against salts, chlorides and carbonation. Designed for use in permanently wet and damp conditions including applications such as: Concrete walls and surfaces in subterranean areas. Water features, tanks and fish ponds (able to be tiled over). Protection of concrete columns, pillars and general surfaces against chloride attack and carbonation Coating of concrete water retaining channels, pits, drains. External waterproof protection on concrete. Recommended to overcoat with Durotech UV protective coatings). Based on unique cross linking polymer technology, Duroflex tank displays outstanding adhesion properties over numerous building substrates including concrete, masonry, renders, screeds and cement based mineral surfaces. No priming is required as Duroflex basement bonds to clean pre-dampened surfaces free of surface water. For applications where finishes need to be applied over this membrane, tiles, renders, textures and solvent free paints are able to be directly applied to the cured Duroflex tank surface.
Sikalastic -1K One component cementitious mortar fibre reinforced for flexible waterproofing.Sikalastic -1K is a one component, flexible, fibre-reinforced mortar, based on cement modified with special alkali-resistant polymers. It also contains fine fillers, selected graded aggregates, plus special waterproofing additives to produce a flexible mortar that is ideal for waterproofing surfaces subject to flexural strain. Sikalastic -1K is suitable for application by brush, roller, trowel or spray equipment. Protection of concrete surfaces according to EN 1504-9, principles 1: protection against penetration (coating); 2: control of moisture (coatings); and 8 increasing resistivity (coating). Waterproof protection of concrete structures including tanks, basins, pipes, etc. Waterproofing external wall surfaces to be backfilled in ground. Internal waterproofing of walls and floors, in basements. Waterproofing of terraces and balconies over concrete or prepared existing tiles. Flexible protection coating for reinforced concrete structures against the effects of de-icing salts, freeze-thaw and carbon dioxide swell consolidation.
Suitable for negative pressure to 25m Can be applied on damp substrates. Easy to apply by brush, roller, trowel or spray equipment. Good sag resistance and easy to apply, even on vertical surfaces. Good crack-bridging properties. Very good adhesion on many substrates including concrete, cement mortars, stone, ceramics, bricks and timber. Mixing ratio can be adjusted in order to obtain the consistency and workability desired for the intended application.
Duromastic ACS-2 is a two part high solids liquid /
cement copolymer membrane with fibre reinforcement. Duromastic ACS-2 cures
rapidly to form a flexible waterproof lining for showers and other wet areas as
described in Australian Standard AS3740:2004 "Waterproofing wet areas
within residential buildings". It complies with AS4858:2004 "Wet Area
Membranes". ACS-2 is particularly suitable for applications where polymer
modified render will be applied or in conditions where other waterbased
waterproofing products have difficulty in drying due to excesive humidity and
coolness. DUROMASTIC ACS-2 forms a waterproof lining to most building materials
including reinforced concrete, cement render, water resistant plaster board,
and compressed cement sheeting etc. The surface must be fixed according to
manufacturers directions and must be clean and dry. DUROMASTIC ACS-2 is
suitable for external use on light pedestrian trafficable decks, parapets and
flashings. Top coat with Duroarmor™ for UV resistance
Features: Simple application - single pack and
water based. Simple application, water based. Fast drying. Good flexibility.
Seamless, no joints or cracks. Environmentally friendly. Good resistance to
Maxseal flex is a two component product: Component A is a mortar based on a mixture of special cements, additives and well-graded fillers and Component B is a liquid based on special synthetic resin. Maxseal flex is a coating with flexible and waterproofing properties that adheres to practically every surface such as concrete, natural and artificial stone, mortar plasters, bricks, concrete blocks, etc.
Once applied and cured, Maxseal flex provides a non-toxic, flexible and waterproof coating that adheres to those common substrates in construction such as concrete, natural and artificial stone, traditional mortar plasters, bricks, concrete blocks.
Waterproofing and protection of water retaining structures, such as drinking water tanks, reservoirs, water mains and swimming pools. Waterproofing of below-grade structures like basements, retaining walls, foundations, tunnels, galleries subjected to both positive or negative high water pressure.
Internal and external waterproofing and protection of new and old buildings, facades against dampness, rain, pollution and aggressive environments.
Waterproofing and protection of concrete against carbonation, freeze-thaw cycles, de-icing salts in highways and chlorine penetration in public works, irrigation channels, dams, retaining walls and water treatment plants, bridges, etc.
Tile fixing and waterproofing of bathrooms, kitchens and other wet rooms in hotels, hospitals, offices and residential buildings, also suitable for exterior applications. Waterproofing of jardinieres, terraces and balconies under the pavement.
Duromastic P15 Diamond
Duromastic P15 Diamond is a polyurethane modified copolymer acrylic waterproofing membrane specifically formulated for bathrooms, laundries, balconies, terraces and other wet areas. Use Duromastic P15 Diamond prior to installing mortar beds, render or tiling. The membrane forms a grey coloured water resistant elastomeric film with excellent durability. Application: Do not apply externally if rain is expected presently. Do not apply below 100oC or above 300oC externally. Ensure that the primer coat is completely dry. Apply evenly and check for missed areas and pin-holes. Apply further coats from cross directions after 4 to 6 hours. Do not apply as one coat. Apply down into drainage outlets. Use reinforcing fabric over expansion joints, cracks, all wall and floor junctions, and pipe penetrations. Apply this by first brushing out a layer of membrane (1-2 mm), next lay in the fabric and ensure there are no air bubbles, and the fabric is fully set in without wrinkles. Then brush over with more membrane. Good air flow and warmth will speed drying
Maxseal Foundation is a construction grade cement based product which, together with special additives and selected aggregates gives it waterproofing characteristics, whether the foundations are in concrete or masonry. It gives great protection to foundation concrete thanks to its high resistance to aggressive waters.
Waterproofing of retaining walls, carparks, basements, elevator pits, tanks and dams.
Good adherence, it becomes incorporated to the support where it is applied, it fills and seals pores.
It can be applied on wet surfaces not needing these to be dried.
Lesser cost than any other traditional system.
Large duration and superior to any others asphalt product.
Unaffected by soil salts. In a positive application.
Easy to apply with tampico type brush, obtaining large yields at its application.
Mapelastic Smart is a two-component mortar based on cementitious binders, fine-grained selected aggregates, special admixtures and synthetic polymers in water dispersion, blended according to a formula developed in MAPEI's own research laboratories. When the two components are mixed, a blend with a plastic consistency is obtained. It may be applied by brush, by roller or by spraying with a worm screw rendering machine on both horizontal and vertical surfaces at a thickness of approximately 2 mm. Due to the content and high quality of the synthetic resins, the hardened layer of Mapelastic Smart remains constantly flexible under all environmental conditions. Mapelastic Smart is waterproof and resistant to the penetration of aggressive substances which are present in the atmosphere, such as carbon dioxide, sulphur dioxide and sulphuric anhydride, and soluble salts such as chlorides and sulphates, which are present in seawater or in the ground. Mapelastic Smart has excellent bonding properties on all cementitious, ceramic and marble surfaces as long as they are sound and sufficiently clean. These properties, together with its resistance to the deteriorating effect of UV rays, a characteristic of this product, ensure that structures protected and waterproofed with Mapelastic Smart have a long service life, even if they are located in areas with particularly rigid climatic conditions, in coastal areas with a saline-rich atmosphere or in industrial areas where the air is particularly polluted. Mapelastic Smart meets the requirements defined by EN 1504-9 ("Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - General principles for the use of products and systems") and the requirements claimed by EN 1504-2 coating (C) according to the PI, MC and IR principles ("Protection systems for concrete surfaces").
WPM 002 (Superflex Two Part) is a tough, fast drying two component waterproofing membrane specifically designed for use under tiles. The product has been uniquely formulated with synthetic microfibers to increase its strength and eliminate the need for a separate reinforcement mat. WPM 002 is based on the most advanced acrylic polymer technology, and is totally resistant to re-emulsification. WPM 002 is flexible, low in odour, and is fully compatible with polymer modified tile adhesives. Wrimco WPM 002 is one of the fastest drying acrylic membranes on the market - normally ready to tile in 16 - 24 hours @23oC. WPM 002 meets the Green Building Council of Australia Green Star IEQ-13 requirements for Architectural Sealant when tested in accordance with SCAQMD Method 304-91 Determination of Volatile Organic Compounds (VOC) in Various Materials as referenced by South Coast Air Quality Management Division (SCAQMD) Rule 1168. Fibre reinforced: Excellent strength, eliminates need for reinforcing mat. Flexible: Accommodates normal building movement. Advanced acrylic: Will not re-emulsify. Designed for tiling: Fully compatible with our tile system adhesives. Water based, low odour and easy cleaning for undertile waterproofing in shower recesses. Conforms to the requirements of AS/NZ 4858:2004 Wet Area Membranes (Ref: CSIRO Report 3879). Critical areas include areas where the membrane is applied at greater than 0.5mm or over impermeable substances such as over bond breakers or incorporating other reinforcement. Longer drying times are necessary in these areas
ACS-3 is a two-part high solids liquid / cement copolymer membrane with fibre
reinforcement. Duromastic ACS-3 cures rapidly to form a flexible waterproof
lining for showers and other wet areas as described in Australian Standard
AS3740:2004 "Waterproofing wet areas within residential buildings".
It complies with AS4858:2004 "Wet Area Membranes". ACS-3 is
particularly suitable for applications where polymer modified render will be
applied or in conditions where other water based waterproofing products have
difficulty in drying due to excessive humidity and coolness. Duromastic ACS-3
forms a waterproof lining to most building materials including reinforced
concrete, cement render, water-resistant plaster board, and compressed cement
sheeting, etc. The surface must be fixed according to manufacturer’s directions
and must be clean and dry. Duromastic ACS-3 is suitable for external use on
light pedestrian trafficable decks, parapets and flashings. Top coat with
Duroarmor for UV resistance
basement is a 1 component polymer enhanced, rigid setting cementitious slurry
coat designed for a range of positive and negative waterproofing applications
over concrete and masonry surfaces. Suitable for underground structures
including retaining walls, basements walls, lift shafts, car parks, building
foundations and footings to prevent water migration through both positive and
negative faces of structures. Once cured Duroflex basement can be finished over
with paint, render and other decorative finishes.Non toxic Excellent adhesion
properties. Fast drying. Dries without cracking, low shrinkage. 1 component,
mixed on site with water, ready to use. Able to withstand positive and negative
water pressure (up to 5m head of pressure on negative side). Protects against
chlorides, sulphates, sea water, subterranean water, freeze thaw and varying pH
water. Suitable on damp concrete or green freshly laid concrete. Can be
finished over with paints, renders and other decorative finishes