Kemseal PU Membrane is a fast cure, liquid applied,
polyurethane elastomeric waterproofing membrane which when fully cured forms a
permanently flexible waterproof lining to most building surfaces including reinforced concrete, block work, brick work,
cement render, plaster board, fibre-reinforced cement sheets, particle board
flooring and plywood etc. Single component. Simple application- liquid applied.
Excellent elasticity. Seamless- no joints or cracks. Fast cure- recoat in 2-4
hours. Smooth, Easy to Apply Formulation. Non sag- Vertical and Horizontal
Application. USE AREAS: Planter boxes. Tanking. Retaining Walls. Balconies and
Decks. Shower Recesses. Flashings. Wet Areas. Walls .
S-80 is a 100% solids fluid applied single component elastomeric silicone
polymer roof coating that cures to provide a long term waterproof and
weatherproof protective seamless membrane layer for roof surfaces. Kemseal S-80
is manufactured using advanced silicone technology to provide superior UV
protection and ponding water resistance that prolongs the life of all existing
roofing systems providing immediate and long term cost and energy savings.
Kemseal S-80 coating (white) meets Cool Roof reflectance performance
requirements for both flat and sloped roofs considerably reducing thermal heat
intake into the building, saving considerable building energy cooling costs.
UV-stable top coat for polyurethane and other
membrane coatings. Protective coating to seal and repair existing roofing and
gutter systems. Restore rusted metal and asbestos cement roofing. Restoration
of aged roof membranes such as; torch-on, EPDM, and other sheet and liquid
applied membranes. Lining Box gutters .
-488/488SL is a high performance, hand-applied, low VOC, moisture curing
single-pack elastomeric polyurethane waterproofing membrane. Sikalastic -
488/488SL is directly foot-trafficable.It
is designed for waterproofing diverse parts of a building including: Balconies
Terraces Podium decks Bathrooms and wet areas Plant room floors Inverted roofs
Undertile beds. UV resistance Seamless membrane High resistance to puncture and
standing water Quick tack-free surface Low VOC High elongation, class III
membrane according to AS/NZS 4858 Crack bridging capability, no reinforcement
needed Elastomeric behaviour Single pack, ready to use Available in various
Maxseal foundation is a construction grade cement based product which, together with special additives and selected aggregates gives it waterproofing characteristics, whether the foundations are in concrete or masonry. It gives great protection to foundation concrete due to its high resistance to aggressive waters. Can be rendered over or painted. Can be rendered over 24 hours after second coat applied - flick or scratch coat must be applied by renderer - After 14 days can be painted over, normal paint procedure on any cement based coatings. Waterproofing of retaining walls, carparks, basements, elevator pits, tanks and dams. Good adherence, it becomes incorporated to the support where it is applied, it fills and seals pores. It can be applied on wet surfaces not needing these to be dried. Lesser cost than any other traditional system. Large duration and superior to any others asphalt product. Unaffected by soil salts. In a positive application. Easy to apply with tampico type brush, obtaining large yields at its application.
400 N Elastic is a one component, UV resistant, highly elastic, moisture curing
polyurethane waterproof membrane. Sikafloor 400N Elastic is suitable for
applications to most common building substrates including concrete, fibre
cement, plasterboard, timber, and some metals. It is suitable for use as a
waterproof membrane for wet areas as described in AS 4858:2004 Wet Area
Membranes. It can be used as a waterproof membrane and coating for: Exposed
roofs, decks, terraces, gutters, flashings, walls. Tanks, reservoirs and pipes.
Shower recesses. Wet areas. Balconies. Retaining walls. Planter boxes. Slab floors
Sikalastic -1K is a one component, flexible, fibre-reinforced mortar, based on cement modified with special alkali-resistant polymers. It also contains fine fillers, selected graded aggregates, plus special waterproofing additives to produce a flexible mortar that is ideal for waterproofing surfaces subject to flexural strain. Sikalastic -1K is suitable for application by brush, roller, trowel or spray equipment. Protection of concrete surfaces according to EN 1504-9, principles 1: protection against penetration (coating); 2: control of moisture (coatings); and 8 increasing resistivity (coating). Waterproof protection of concrete structures including tanks, basins, pipes, etc. Waterproofing external wall surfaces to be backfilled in ground. Internal waterproofing of walls and floors, in basements. Waterproofing of terraces and balconies over concrete or prepared existing tiles. Flexible protection coating for reinforced concrete structures against the effects of de-icing salts, freeze-thaw and carbon dioxide swell consolidation. Suitable for negative pressure to 25m. Can be applied on damp substrates. Easy to apply by brush, roller, trowel or spray equipment. Good sag resistance and easy to apply, even on vertical surfaces. Good crack-bridging properties. Very good adhesion on many substrates including concrete, cement mortars, stone, ceramics, bricks and timber. Mixing ratio can be adjusted in order to obtain the consistency and workability desired for the intended application .
WPA 990 PU
WPA 990 is a single pack, liquid applied, moisture cured polyurethane waterproofing membrane, suitable for waterproofing most non-exposed applications. WPA 990 cures to form a seamless, tough, durable, elastomeric waterproofing membrane. WPA 990 has excellent adhesion to most suitably primed building substrates and is suitable for above and below ground applications. Recommended for: Retaining Walls. Planter Boxes. Features and Benefits: Class III membrane in accordance with AS 4858 and AS 4654.1. Fast curing. Tar and Bitumen free. Permanently flexible. Good Chemical resistance. Excellent adhesion to a wide variety of substrates. Single pack.
Highly flexible - over 900% elongation. No seams or laps. Generally no priming required. Single layer application possible. Ready for immediate use (no mixing required). Accommodates crack movement from 0 to 1.6mm when fully cured at 1.3mm thickness. Withstands hydrostatic pressure of up to 4m head of water while bridging a crack of 1.5mm width. Over 15 years proven performance. Available in self-levelling (H) grade or rollable grade (R) for easy application. TREMproof 60 is a single component, bitumen modified, moisture curing polyurethane fluid applied waterproofing membrane. Usage/Purpose: Roofs, Tunnels. Terraces, Balconies, Plaza Decks, Planter Boxes, Retaining Walls, Fountains and Pools. Concrete surfaces shall be cured for a minimum of 28 days. Surface should have light steel trowel finish followed by a fine hair broom or equivalent finish. Substrate should be free from dust, oil, curing agent resi- dues and other contaminants. All shrinkage and non moving structural cracks under 1.5mm shall be filled with not less than 1.5mm (1500 wet microns) of TREMproof 60R extending 75mm to both sides of the crack. Cracks wider that 1.5mm should be routed to 6mm width and 13mm depth. Install a closed cell polyethylene backing rod and seal with TREMproof 60R extended to 75mm either side of the joint. Wherever a vertical penetration exists (eg parapet walls, columns, stacks etc.) install a 25mm fillet of TREMproof 60R at the point where the vertical and horizontal surfaces intersect. The TREMproof 60 membrane should then be applied over the fillet to a height of approximately 75mm to form an overflashing. Voids and honeycomb must be patched with a non-shrinking, quick setting grout. Allow the patched area a minimum of 7 days to cure.
Ardex WPM 368
Water resistant, prevents rising damp, substrate efflorescence and withstands hydrostatic pressure. Leading edge innovative technology for liquid applied membranes. Excellent adhesion to most substrates including damp surfaces and freshly laid green concrete. Built in mechanical key, sand blinding not required Suitable for under tiles and under floor levelers. Suitable as an incontinence barrier to concrete floors prior to carpet and carpet tile installation. Ardex WPM 368 is a single component acrylic copolymer membrane that will prevent rising damp, efflorescence and will resist negative hydrostatic pressure when used in accordance with the technical data sheet. It has excellent adhesion to most substrates including brick, masonry, concrete block, concrete, stone and is simple to use by brush, roller or airless spray machine. Ardex
WPM 368 single part damp-proof is safe to use and can be over-coated using almost any decorative paint. Ardex
WPM 368 can be applied to damp surfaces and freshly laid hardened (green) concrete and conforms to the Building Code of Australia as a waterproof membrane. Features/Benefits: Non-flammable and negligible odour. Can be applied to damp surfaces. Can be safely applied to freshly laid hardened (green) concrete. When applied directly to the substrate (dual coat system) the cured membrane will withstand 250kPa of hydrostatic pressure which is equivalent to a 25 metre head of water. Can be over coated using almost any decorative or industrial finishing paint. Prevents rising damp and the formation of efflorescence when used as a dual coat system. Typical Application: As a low water vapour transmission coating in the building and construction industries and as a barrier/seal coating over freshly laid or damp concrete. As a hydrostatic pressure resistant waterproofing membrane to prevent water seepage or dampness penetration through to the interior of walls and floors. As a waterproofing barrier on the negative side in below grade surfaces such as basements, tunnels, lift wells, retaining walls and carparks. As a waterproofing membrane or barrier coating over freshly laid hardened (green) concrete, prior to the application of conventional levelling compounds, carpet and tile adhesives. As a barrier seal coating over damp, green or efflorescence producing concrete prior to over coating with conventional building paints. For use as a waterproof barrier prior to applying ARDEX floor levellers and tile adhesives.
Maxseal flex is a coating with flexible and waterproofing properties that adheres to practically every surface such as concrete, natural and artificial stone, mortar plasters, bricks, concrete blocks, etc. subjected to both positive or negative high water pressure waterproof coating that adheres to common substrates in construction such as concrete, natural and artificial stone, traditional mortar plasters, bricks, concrete blocks. once applied and cured, Maxseal flex provides a non-toxic, flexible and waterproof coating that adheres to those common substrates in construction such as concrete, natural and artificial stone, traditional mortar plasters, bricks, concrete blocks. can be rendered over or painted. can be rendered over 24 hours after second coat applied - flick or scratch coat must be applied by renderer - after 14 days can be painted over, normal paint procedure on any cement based coatings. Maxseal flex is a two component product: component a is a mortar based on a mixture of special cements, additives and well-graded fillers and component b is a liquid based on special synthetic resin. Maxseal flex is a coating with flexible and waterproofing properties that adheres to practically every surface such as concrete, natural and artificial stone, mortar plasters, bricks, concrete blocks, etc. once applied and cured, Maxseal flex provides a non-toxic, flexible and waterproof coating that adheres to those common substrates in construction such as concrete, natural and artificial stone, traditional mortar plasters, bricks, concrete blocks. Application fields: waterproofing and protection of water retaining structures, such as drinking water tanks, reservoirs, water mains and swimming pools. waterproofing of below-grade structures like basements, retaining walls, foundations, tunnels, galleries subjected to both positive or negative high water pressure. internal and external waterproofing and protection of new and old buildings, faÃ§ades against dampness, rain, pollution, and aggressive environments. waterproofing and protection of concrete against carbonation, freeze-thaw cycles, de-icing salts in highways and chlorine penetration in public works, irrigation channels, dams, retaining walls and water treatment plants, bridges, etc. tile fixing and waterproofing of bathrooms, kitchens and other wet rooms in hotels, hospitals, offices and residential buildings, also suitable for exterior applications. waterproofing of jardinieres, terraces and balconies under the pavement.