Bostik Aquashield SB40 is a protective water-resistant sealer to protect and treat masonry and cementitious structures for the prevention of water absorption. Used in conjunction with both Bostik Dynacryl and Bostik Wetlook to form a complete concrete protection system that is highly penetrative to form an invisible, breathable impregnating sealer. Bostik Aquashield SB40 impregnates concrete to protect from ingress of salts, chlorides. It protects reinforced concrete from waterborne chloride ions making it an ideal protective surface treatment. Bostik Aquashield SB40 is designed to impregnate the concrete surface and permanently bond to the molecular structure of the concrete, thus changing its absorption characteristics.
Bostik Dynacryl is a solvent based clear acrylic coating for a protective and decorative coating for concrete and masonry. Suitable for use on all types of structures whether they are new or old, providing a waterproof clear gloss finish, hard wearing and durable. It provides a tough layer to a variety of surfaces. Bostik Dynacryl UV filter ensures a finish that is durable under
Australia's harsh weather conditions. Available in clear. Bostik Dynacryl protects concrete from aggressive atmosphere, moisture ingress and carbonation. Bostik Dynacryl dramatically reduces the penetration of carbon dioxide through to the concrete, while at the same time allows the concrete to breathe. Note: It should be remembered that the application of sealers to any surface will reduce the natural slip resistance that these surfaces have. This is particularly important in external or internal areas where the surface will be subject to wetting e.g. pool surrounds, external pathways etc. Bostik Dynacryl is not recommended for clay pavers, clay bricks, ceramic, terracotta or quarry tiles.
Decofloor is a new approach to coloured-flake flooring which uses state of the art decorative coatings technology to provide a coating system with low odour, extremely low volatile organic content and excellent resistance to abrasion and staining.
Solvent free coloured epoxy basecoat (Bostik EPOXYCOTE HS). Solvent free clear epoxy topcoat for internal areas out of direct sunlight. Extremely Low Volatile Organic Content. Excellent abrasion resistance. Unaffected by most household chemicals including engine oil. Wide range of coloured flake blends available. (REFER TO COLOUR CHART). Easily maintained. Solvent based UV resistant clear polyurethane available for areas in direct sunlight.
Bostik Flexithane is ultra-violet light resistant single pack clear polyurethane which cures by reaction with moisture in the air to an extremely tough and durable film. It is suitable for use on interior cork, timber and masonry surfaces where the finished coating provides a chemical resistant, long wearing, floor treatment suitable for use in traffic areas. Bostik Flexithane contains a high level of ultraviolet absorber which enables it to protect substrates from discolouration caused by sunlight. It can be used either as the entire finish system or as a protective glaze finish over conventional polyurethane and epoxy flooring systems.
Wet look is a pure acrylic sealer, designed to enhance and protect masonary surfaces. On drying, Wet look produces a classic wet look finish, with an appealing gloss level. Suitable surface: Slate. Stone. Clay and concrete paving, exposed aggregate (both poured and paving bricks), clay brick, concrete block and reconstituted limestone walls (sacrificial anti graffiti).
Suregrip is a high performance slip resistant, water based, coloured coating designed for easy application to asphalt, concrete, steel & timber.
All surfaces must be free or cleaned of all dirt, dust, grease, oil, fuels, chemicals, other contaminants particles. Note: Further instructions for various surfaces follows: ASPHALT: Along with general cleaning above, apply high pressure water sufficiently to remove all loose and foreign matter and allow drying thoroughly. PRIMING ASPHALT: Apply AVS PROTECTIT 600M by roller or brush or spray at approximately 7 m2 to 10 m2 per litre depending on porosity of asphalt. Allow min. 2 hrs in good drying conditions before application of Bostik SUREGRIP. CONCRETE: New concrete should cure for 28 days prior to coating. Along with GENERAL CLEANING above, remove concrete laitance with an acid-etch mixture of 1 part Hydrochloric Acid and 4 parts Water. Use plastic watering can to apply acid mixture, agitate the mixture on the concrete with a stiff broom before rinsing using high pressure water while the slurry is still wet. Acid mixture must not contact timber or metal surfaces. Allow to dry thoroughly. When acid-etching is not practical, use sufficient sanding, scabbling or grinding to remove surface contaminants, concrete laitance etc. Dust encapsulation equipment is recommended.