Duroflex tank is a two
component polymer modified cementitious coating designed for waterproofing
concrete and masonry surfaces in a variety of applications. Applied by roller,
brush, trowel or spray methods, once cured Duroflex tank provides a protective
barrier to concrete surfaces against salts, chlorides and carbonation. Designed
for use in permanently wet and damp conditions including applications such as: Concrete
walls and surfaces in subterranean areas. Water features, tanks and fish ponds
(able to be tiled over). Protection of concrete columns, pillars and general
surfaces against chloride attack and carbonation Coating of concrete water retaining
channels, pits, drains. External waterproof protection on concrete. Recommended
to overcoat with Durotech UV protective coatings). Based on unique cross
linking polymer technology, Duroflex tank displays outstanding adhesion
properties over numerous building substrates including concrete, masonry,
renders, screeds and cement based mineral surfaces. No priming is required as
Duroflex basement bonds to clean pre-dampened surfaces free of surface water.
For applications where finishes need to be applied over this membrane, tiles,
renders, textures and solvent free paints are able to be directly applied to
the cured Duroflex tank surface.
Kemseal P14-Fibre
is a liquid applied polyurethane
modified copolymer waterproofing membrane containing a fibrous filament
reinforcing. When fully cured, Kemseal P14-Fibre forms a Class III flexible
waterproof lining to showers and wet areas as described in AS 4858- 2004.
Waterproofing Wet Areas within Residential buildings. Kemseal P14-Fibre
may be applied to most building materials including reinforced concrete, cement
render, wet area plasterboard, compressed fibre-cement sheeting, plywood and
particleboard wet area flooring. USE AREAS: Shower Recesses. Wet Areas.
Flashings. Balconies and Decks. Exposed Roof. Walls
CLASS II for Showers, Decks, Roofs and Balconies. It is a two part liquid / cement copolymer membrane with fibrous reinforcement. It cures rapidly to form a flexible waterproof lining for showers and other wet areas as described in Australian Standard AS3740:2004 "Waterproofing wet areas within residential buildings" & complies to S4858:2004 "Wet Area Membranes". It forms a waterproof lining to most building materials including reinforced concrete, cement render, water resistant plaster board, and fibre reinforced cement sheet flooring, etc. The surface must be firmly fixed to manufacturers directions, and must be clean and dry. It is suitable for external use on light pedestrian trafficable decks, parapets and flashings. Top coat with Duromatic SR for UV resistance.
Kemseal
MGP
is a multi-grade moisture cure, polyurethane waterproofing membrane which
when fully cured forms a permanently flexible elastomeric waterproof membrane
lining to most building surfaces including reinforced concrete, block work,
brick work, cement render, plaster-board, fibre-reinforced cement sheets,
particle board flooring and plywood etc. Principle characteristics: Single
component. Simple application- liquid applied. Excellent elasticity. Seamless-
no joints or cracks. Fast cure- recoat in 2-4 hours. Smooth, Easy to Apply
Formulation. Non sag- Vertical and Horizontal Application. USE AREAS: Planter
boxes. Tanking. Retaining Walls. Balconies and Decks. Shower Recesses.
Flashings. Wet Areas. Walls. Roof Tops (non-exposed). Kemseal MGP is often
self-priming when used on internal surfaces eg. villaboard, chipboard, sound
concrete, block work. Absorbent surfaces may require priming with Kemseal MGP
thinned with 20 - 50% Xylene< Kemseal SP1 solvent primer or Kemseal WBE
applied at 6 m2/Litre. Prime damp areas and areas subject to rising damp with
Kemseal WBE. Plastic/Plumbing fittings shall be primed with Kemseal WBE. Allow
to fully cure prior to membrane application
Kemseal PU
Kemseal PU Membrane is a fast cure, liquid applied,
polyurethane elastomeric waterproofing membrane which when fully cured forms a
permanently flexible waterproof lining to most building surfaces including
reinforced concrete, block work, brick work,
cement render, plaster board, fibre-reinforced cement sheets, particle board
flooring and plywood etc. Single component. Simple application- liquid applied.
Excellent elasticity. Seamless- no joints or cracks. Fast cure- recoat in 2-4
hours. Smooth, Easy to Apply Formulation. Non sag- Vertical and Horizontal
Application. USE AREAS: Planter boxes. Tanking. Retaining Walls. Balconies and
Decks. Shower Recesses. Flashings. Wet Areas. Walls.
WPA 990 PU
WPA
990 is a single pack, liquid applied, moisture cured polyurethane waterproofing
membrane, suitable for waterproofing most non-exposed applications. WPA 990
cures to form a seamless, tough, durable, elastomeric waterproofing membrane.
WPA 990 has excellent adhesion to most suitably primed building substrates and
is suitable for above and below ground applications. Recommended for: Retaining
Walls. Planter Boxes. Features and Benefits: Class III membrane in accordance
with AS 4858 and AS 4654.1. Fast curing. Tar and Bitumen free. Permanently
flexible. Good Chemical resistance. Excellent adhesion to a wide variety of
substrates. Single pack.
Bostik Dampfix PU
One component, highly elastic, class 3, polyurethane waterproofing membrane system that contains no bitumen and complies with AS/NZ 4858. This Technical Data Sheet may be revised, as appropriate, to comply with changes to relevant Australian Standards, reflect changes in Industry best practice in waterproofing procedures or include improvements to current technologies. Bostik Dampfix PU polyurethane waterproofing membrane is specifically formulated for applications where the waterproofing membrane is to be covered by tiling systems laid on an unbonded reinforced screed to falls (ref: Guide to the Installation of Ceramic Tiles - AS3958.1). This is a 2-coat system applied over primed porous & non-porous substrates. It is not recommended as a membrane system in immersed areas (such as pools or spas)
Dampfix Gold Dampfix Gold:
One part, highly elastic, Class 3, water-based polyurethane waterproofing membrane system that meets the requirements of AS3740 by complying with AS/NZ 4858. The Bostik Dampfix Gold waterproofing membrane system is specifically formulated for application on graded substrates that provide positive falls to drainage outlets. Overlaying tiling systems must comply with Guide to the Installation of Ceramic Tiles - AS3958.1). This is a 2-coat system applied over primed porous & nonporous substrates. It is not recommended as a membrane system in immersed applications (such as pools or spas)
Roofshield PU
Roofshield PU is a premium quality elastomeric
polyurethane membrane specifically designed to be used as a roof membrane where
a strong UV resistant flexible good quality membrane is required. Roofshield PU
has a higher urethane content and added fibre resulting in a strong durable
membrane with improved flexibility and longer life. Compliant to class III
category AS4858:2004 - Internal Wet Areas Waterproofing. Compliant to AS 4654.2-2012 - Waterproofing Membranes for
External Above Ground Use. Easy to use. Fibre reinforced. High urethane
content. Improved flexibility. High UV resistance. Durable and tough.
Environmentally safe. Fast drying. Easy clean up. Salt and carbon attack
resistant. USES: Roofs. Balconies and podiums. External wet areas. Building
facades. Surfaces requiring a high quality UV resistant coating.
Roofshield PU can be applied with a brush or
roller. Apply product at a minimum of 2 coats and at a total coverage of
1.5-2L/m2, forming a dried film thickness of approximately 1.5mm (vertical
0.8mm). Allow 24 hours drying before tiling or topping application. In cool or
non-porous surfaces this may be prolonged. Allow to cure for at least 5 days if
water ponding test is required. At all junctions apply bond breaker or fast
cure mastic fillet. At all junctions embedded polyester/rubber reinforcing tape
into membrane. Do not apply when surface temperature is below 5oC or above 35oC.
Overcoat: Allow at least 4 hours of curing time depending on the weather
Duromix Hibuild WBE
is a two component water based epoxy coating
used to prime seal, coat concrete and masonry surfaces. It cures to a
tough chemical and water resistant coating having excellent adhesion to
sound concrete. Packaging: 20 litre, 4 litre. Water based, user
friendly. Low odour. Environmentally friendly. Excellent water resistance. Excellent
oil resistance. Excellent adhesion to fresh concrete. Applicable to damp
surfaces. Resists hydrostatic pressure when cured. Requires a UV resistant top
coat when in direct sunlight. USE AREAS: Fish ponds. Retaining walls. Reverse
tanking. Primer for acrylic & polyurethane membrane. Dust sealing concrete
floors. Waterproofing concrete slabs before vinyl and timber overlays. Concrete
curing membrane. Moisture barrier on damp walls/floors.
Ardex WPM002
WPM 002 (Superflex Two Part) is a tough, fast drying two
component waterproofing membrane specifically designed for use under tiles. The
product has been uniquely formulated with synthetic microfibers to increase its
strength and eliminate the need for a separate reinforcement mat. WPM 002 is
based on the most advanced acrylic polymer technology, and is totally resistant
to re-emulsification. WPM 002 is flexible, low in odour, and is fully
compatible with polymer modified tile adhesives. Wrimco WPM 002 is one of the
fastest drying acrylic membranes on the market - normally ready to tile in 16 -
24 hours @ 23 C. WPM 002 meets the Green Building Council of Australia Green
Star IEQ-13 requirements for Architectural Sealant when tested in accordance
with SCAQMD Method 304-91 Determination of Volatile Organic Compounds (VOC) in
Various Materials as referenced by South Coast Air Quality Management Division
(SCAQMD) Rule 1168.
Fibre reinforced: Excellent strength, eliminates
need for reinforcing mat. Flexible: Accommodates normal building movement. Advanced
acrylic: Will not re-emulsify. Designed for tiling: Fully compatible with our
tile system adhesives. Water based, low odour and easy cleaning for undertile
waterproofing in shower recesses. Conforms to the requirements of AS/NZ
4858:2004 Wet Area Membranes (Ref: CSIRO Report 3879). *Critical areas include
areas where the membrane is applied at greater than 0.5mm or over impermeable
substances such as over bond breakers or incorporating other reinforcement.
Longer drying times are necessary in these areas
Duroproof PUM
Duroproof
PUM is a tough, durable, elastomeric, single pack, liquid applied, moisture
curing, cross-linking, polyurethane waterproofing membrane - usually grey in
colour. Duroproof PUM forms a tough,
flexible, seamless waterproofing membrane designed for both vertical and
horizontal surfaces that bonds well to most suitably primed building
substrates. Duroproof PUM is formulated as an anti-sag membrane, that although
easy to apply by roller or brush, it can be applied on to vertical surfaces
without slumping to achieve the require film thicknesses. Single pack, no
mixing. Fast curing (usually within 24 hour). Anti-sag (maintains required
thickness without slumping on vertical surfaces). Permanently flexible (tests
show initial flexibility of > 500%). Will not bleed or stain grout or tiles.
Good chemical resistance. High strength and puncture resistant. Provides
seamless membrane (no joints or laps).Easily repaired and or
maintained. Odourless when cured. Formulated to provide long term protection. Tar
free. Easy to apply