ARDEX WPM 3000X (Shelterseal 3000X Self Adhesive Membrane) is a peel and stick bituminous/asphalt membrane protected by a cross laminated high-density polyethylene film. ARDEX WPM 3000X is made from two structural components. Bitumen/asphalt compound modified with SBS and high tack resins. This special compound has been formulated to make the product easy to install. The membrane can be adjusted should it initially be placed in the wrong position, as the adhesive on the sheet achieves final adhesion only after a few minutes. Protective film This is hot-laminated to the bituminous/asphalt compound and gives the membrane its mechanical and physical characteristics, such as heat stability, shape, chemical resistance, etc.
FEATURES/BENEFITS
Cold application Installed without the use of open flames. Ideal for installation in restricted spaces. Chemical resistance The protective polymer film is highly resistant to acids, alkalis and other pollutants. Flexibility and adaptability This membrane will adapt easily to irregularly shaped surfaces, and will stretch without breaking or cracking. Self sealing The membrane self seals on contact with substrate maintaining its watertightness. Constant thickness The membrane is manufactured using high-tech machinery which constantly monitors its thickness, and ensures that the films and synthetic materials are manufactured to the highest specifications and quality control requirements.
ACCEPTABLE SUBSTRATES
-
Concretes, renders and screeds.
-
Fibre cement sheets.
-
Structural or marine plywood.
-
Polystyrene blocks.
For use over other substrates including existing membranes contact ARDEX.
TYPICAL APPLICATIONS
-
Planter boxes.
-
Foundations.
-
Below-ground applications.
-
Retaining walls.
-
Balcony Decks under cement screeds.
BASIC APPLICATION INSTRUCTIONS
Surface preparation Surfaces to which the ARDEX WPM 3000X is to be installed must be properly prepared prior to installation. All surfaces must be clean, dry, smooth, free of sharp edges, loose or foreign materials, oil, grease, and other materials that may damage the membrane. If concrete has moisture on surface apply one coat of ARDEX WPM 300 at a coverage rate of 3.0m2/L and allow to cure for at least 3 days prior to proceeding.
Priming
Prior to the application of the membrane all prepared surfaces (except polystyrene blocks) should be primed with ARDEX WPM 240 (Shelterbit Primer) at a rate of 5-6m2 per litre and allowed to dry. For priming polystyrene blocks ARDEX WPM 300 is required.
Application of ARDEX WPM 3000X
ARDEX WPM 3000X should always be applied from the lowest point to enable laps to shed water. All edge and end laps must be overlapped a minimum of 60mm. Internal and external corners shall be reinforced with an extra layer of membrane 300mm wide. All end laps and exposed edges should be sealed. On vertical surfaces the installation should start at the lowest point with the joints overlapping by at least 100mm, and formed so that they will shed water. All rolls of ARDEX WPM 3000X are marked with a 60mm line for overlapping. Ensure that the membrane is properly adhered to the surface at perimeters or around penetrations. On completion of the installation of ARDEX WPM 3000X it is recommended that a protection board be used before back filling to protect the membrane from damage. Under no circumstances should the membrane be left exposed to UV light for long periods.
Two layer DPC system
In critical areas a specifier may require a second layer of ARDEX WPM 3000X to be applied with laps staggered to the first layer. ARDEX WPM 3000X should be installed by approved applicators, well trained in the application of self-adhesive membranes. Installation shall be strictly in accordance with ARDEX recommendations.
SAFETY PRECAUTIONS
ARDEX WPM 3000X is hazardous; non-dangerous goods. Wear eye/face protection. Use only in well ventilated areas. Keep rolls in well ventilated place. In case of contact with eyes, rinse with plenty of water and contact a doctor or Poisons Information Centre. ARDEX WPM 240 is hazardous; dangerous goods. It is highly flammable, harmful if swallowed and irritating to the eys and skin. Keep away from sources of ignition. No smoking. Keep container tightly closed and in a well ventilated place. Additional information for ARDEX WPM 3000X is found in the Material Safety Data SHeet.
STORAGE
All rolls of ARDEX WPM 3000X, whether palletised or loose, should be stored in a cool covered area protected against sunlight and UV radiation. Rolls should be stored in a vertical position on a smooth floor so as not to damage the edges.
PACKAGING
Roll size: 1m x 20m Roll weight: Approx 30kg Other products: ARDEX WPM 240 (Shelterbit Primer) - 20L Rolls per pallet: 25
.
|